|
Remote Reboot Switches
and Remote Power Control
When network devices lock-up,
the problem can often be corrected by cycling power off and on in order
to initiate a reboot. Although this procedure is simple when the device
is located in the next room, it can be troublesome and expensive if the
device is located at a remote site. WTI's remote power control and reboot
products provide a reliable, cost effective way to re-start "locked-up"
devices at remote locations, using ASCII commands sent via modem or network.
 |
 |
NBB-1600 |
|
| |
| 16-Plug Network Boot Bar |
| The new NBB-1600 Network Boot Bar allows you to control 115 VAC power on up to sixteen different devices. Like it's sister unit, the NBB, the NBB-1600 also features "Zero Unit" mounting, allowing you to add power control capabilities to your equipment rack, without sacrificing rack space. The NBB-1600 includes two separate AC power circuits, and each circuit will accept a load of up to 15 amps maximum. The easy-to-use Web Browser interface provides simple, yet effective control of switching, reboot and configuration functions, and a handy ASCII Text Interface allows command mode access for those who prefer to control the unit via Telnet. The NBB-1600 also features two different levels of password protected security; an administrative level which can be used to control switching and reboot functions and select configuration parameters, and a user level which has switching and reboot capability, but does not permit redefinition of unit parameters. Passwords are transmitted using basic 64 bit encryption to ensure that command mode access remains secure. More Information |
|
 |
 |
NBB-115 |
|
| Network Boot
Bar |
The
new NBB-115 Network Boot Bar provides a convenient means
for 115 VAC power control for rack mounted equipment and
other devices. The NBB-115 features "Zero Unit" mounting,
which allows you to add power control capabilities to your
equipment rack, without sacrificing valuable rack space.
An easy-to-use Web Browser interface provides simple, yet
effective control of switching, reboot and configuration
functions, and a handy ASCII Text Interface allows command
mode access for those who prefer to control the unit via
Telnet. The NBB-115 also features two different levels of
password protected security; an administrative level which
can be used to control switching and reboot functions and
select configuration parameters, and a user level which has
switching and reboot capability, but does not permit redefinition
of unit parameters. If colocation is an important factor
in your application, users can also be limited to only specific
plugs based on the password entered at login. Passwords are
transmitted using basic 64 bit encryption to ensure that
command mode access remains secure.
More Information |
|
 |
| |
NBB-230 |
|
| |
| Network Boot
Bar |
WTI's new, NBB-230
Network Boot Bar allows you to remotely control power and initiate
reboot cycles on 230 VAC rack mounted equipment. Like it's
115 VAC cousin the NBB-115, this 230 VAC version of the NBB
also features "Zero
Unit" mounting, allowing you to add remote power control capability
to your equipment rack, without sacrificing valuable rack space.
The NBB-230 also features a user-friendly Web Browser interface,
to provide simple, yet effective control of switching, reboot
and configuration functions, and a clear, easy-to-master ASCII
Text Interface for applications that require command initiated
control of power functions via Telnet. Two different levels of
password protected security are provided: an administrative level,
which allows access to switching, reboot and configuration functions,
and a user level which permits switching and reboot functions,
but does not permit access to configuration menus. If colocation
is an important factor in your application, users can also be
limited to only specific plugs based on the password entered
at login. Passwords are transmitted using basic 64 bit encryption
to ensure that command mode access remains secure.
More Information |
|
 |
NPS-115/230
Telnet & Dial-Up Network Power Switch
Control eight individual plugs, up to 30 amps AC, via Telnet and/or
dial-up modem and local terminal with the new NPS-115 Network Power
Switch. Our NPS series network power switches provide network administrators
with the ability to cycle power off and on from anywhere on the LAN/WAN.
If your network is down, the NPS also allows the user to simply dial-in
from a standard modem for out-of-band power control.
More Information |
 |
NPS-2HD
Heavy Duty, Telnet & Dial-Up
Power Switch
The new NPS-2HD Heavy Duty Telnet & Dial-Up Power Switch is ideal
for applications that require remote switching of high-amp 115 VAC
powered equipment such as power supplies on routers and other equipment.
The unit includes two separate 20 amp circuits, each with it's own
power input connector. This heavy duty network power switch includes
all of the convenient remote access features available on our standard
NPS series units, allowing communication via dial-up connection, local
terminal or TCP/IP network.
More Information |
 |
TPS-2
Telnet & Dial-Up Power Switch
The economical TPS-2 Telnet Power Switch is a two-plug version of
our popular NPS-115 Network Power Switch. The TPS-2 unit features
two independently controlled 115 VAC plugs, and includes all of
the innovative features that make the NPS-115 one of our fastest
selling items. In addition to allowing network and/or modem based
control of the two switched plugs, the TPS-2 also features a convenient,
manual-override switch for each plug.
More Information |
 |
| |
TPS-2
CE |
|
| 230 VAC Telnet
& Dial-Up Power Switch |
The TPS-2 CE Telnet Power Switch
provides an ideal solution for network administrators who need
a reliable, economical means for controlling 230 VAC power at
remote installation sites. Like the standard TPS-2, the TPS-2
CE is also a two plug version of our popular NPS Series Network
Power Switches. However, in this case, the TPS-2CE includes
two independently controlled 230 VAC plugs, plus the advanced
control and configuration features found in our popular NPS-230
models. In addition to allowing network and/or modem based control
of the two switched plugs, the TPS-2 CE also features a convenient,
manual-override switch for each plug.
More Information |
|
 |
| |
IPS-15 |
|
| Internet Power
Switch |
The
new IPS-15 Internet Power switch allows you to use your web
browser to reboot remote units and control power at remote
installation sites. In addition to the web browser control
interface, the IPS-15 also features a convenient ASCII command
line interface, which allows the unit to be controlled by
commands issued by software. Access to both the web browser
interface and command line interface is password protected
to prevent unauthorized users from gaining access to power
control functions. Passwords are transmitted using basic
64 bit encryption to ensure that they remain protected and
that access to your equipment remains secure.
More Information |
|
 |
| |
IPS-15
CE |
|
| 230 VAC Internet
Power Switch |
WTI's IPS-15-CE 230 VAC Internet
Power Switch allows you to use your Javascript enabled web
browser to reboot remote devices and control power at far-away
installation sites. With the IPS-15-CE, 230 VAC power can be
switched on, off or rebooted with the click of a mouse, without
leaving your office! In addition to the convenient Web interface,
the Internet Power Switch can also be controlled using simple
ASCII commands, making the IPS the perfect solution for applications
where power switching functions are controlled by commands
issued by software. Both the web browser interface and ASCII
command interface are password protected to prevent unauthorized
users from gaining access to power control functions. Passwords
are transmitted using basic 64 bit encryption to ensure that
they remain protected and that access to your equipment remains
secure.
More Information |
|
 |
RPC-230
High Amp AC Intelligent Remote Power Control
Router and communications equipment sometimes "locks-up"
and must be re-booted in order to come back on line. This often requires
a trip to the installation site, simply to flip the power switch off
and then back on. When distance makes this costly or time consuming,
WTI's Remote Power Controller can be connected to a modem, terminal
server or other communications device, to literally switch power off
and back on from anywhere.
More Information |
 |
RPC-48
High Amp -48VDC Intelligent Remote Reboot Switch (One or Two Terminals)
The RPC-48 provides remote reset capability for high-amp -48 VDC network
equipment. Many network devices, such as Enterprise routers require
up to 35 amps of -48 VDC power; the RPC-48 supports these high-amp
requirements, with capacity to spare. The RPC-48 features password
protection, on-screen circuit labels to identify connected devices,
a site ID message, and a user-friendly ASCII command set.
More Information |
 |
RPB+ 115
115V Intelligent Remote Power Control/Reboot Bar
The RPB+ is an intelligent power control and reboot switch, which
can be operated from a remote location via modem. Up to five connected
115 VAC devices can be rebooted or powered On or Off in response to
simple ASCII commands sent via modem or from a local PC. Configuration
is simple; a convenient menu system displays current plug conditions
and communication parameters. The RPB+ provides password protection,
on-screen plug labels to identify connected devices, a site ID message,
and a user-friendly ASCII command set.
More Information |
 |
RPB+ 230
230V Intelligent Remote Power Control/Reboot Bar
The RPB+ 230 provides the same convenient RPB+ power control/reboot
features for 230 VAC applications. Up to five connected 230 VAC devices
can be rebooted, or powered On or Off in response to simple ASCII
commands sent via modem or from a local PC. Status screens display
current plug conditions and user-selected parameters. The RPB+ 230
also provides password protection, on-screen plug labels, a site ID
message and the same user-friendly ASCII command set.
More Information |
 |
| |
RPC-4840N |
|
Telnet
+ Dial-Up High Amp -48 VDC Intelligent Remote Reboot Switch
(One or Two Terminals)
The RPC-4840N provides remote reset capability for high-amp,
-48 VDC network equipment. Boot/On/Off commands can be sent
to the unit via TCP/IP network, via modem, or from a local PC
connected directly to the RPC console port. Many network devices,
such as Enterprise routers require up to 35 amps of -48 VDC
power; the RPC-4840N supports these high-amp requirements, with
capacity to spare. The RPC-4840N features a 10Base-T Ethernet
port, a dedicated external modem port, password protection,
on-screen circuit labels to identify connected devices, a site
ID message, and a user-friendly ASCII command set.
More Information |
|
 |
RPB+ DC30
48 VDC Intelligent Remote Reboot Switch (Five Terminals)
The RPB+ DC is designed for applications that require remote reset
capability for 48 VDC equipment. The RPB+DC provides the same convenient
features as our other RPB+ series reboot bars. Up to five connected
48 VDC devices can be rebooted or powered On or Off in response to
simple ASCII commands sent via modem or from a local PC. Status Screens
display circuit conditions and user-selected communication parameters.
This 48 VDC version of the RPB+ also features password protection,
on-screen circuit labels, a site ID message and a user-friendly ASCII
command set. The RPB+ DC is ideal for use with -48 VDC powered routers,
servers, and telecom equipment.
More Information |
 |
RPB-115
115VAC "low-cost" Remote Reboot Switch
The RPB-115 is a "low-cost" alternative to the RPB+115.
The RPB-115 is an intelligent power control and reboot switch, which
can be operated from a remote location via modem. Up to five connected
115 VAC devices can be rebooted or powered On or Off in response to
simple ASCII commands sent via modem or from a local PC. Configuration
is simple; a convenient menu system displays current plug conditions
and communication parameters.
More Information |
 |
RPS-10
115VAC Power Control/Reboot Unit (One Plug, Expandable)
The RPS-10 provides an expandable, code controlled solution for your
power control/reboot application. The RS-232 controlled RPS-10 Master
Module provides power control for one AC outlet. When your reboot
needs expand, additional RPS-10 Satellite Modules can be added to
allow individual control of up to ten AC outlets. Modules are linked
together using standard RJ-11 style cable, for a maximum end-to-end
length of 2000 feet.
More Information |
 |
RPS-10 EC
230VAC Power Control/Reboot Unit (One Plug, Expandable)
A 230 VAC version of our RPS-10 expandable, code controlled power
control/reboot system. A single RPS-10 EC Master Module provides power
control for one 230 VAC outlet. When reboot needs expand, additional
RPS-10 EC Satellite Modules can be added to allow individual control
of up to ten 230 VAC outlets. Modules are linked together using standard
RJ-11 style cable, for a maximum end-to-end length of 2000 feet.
More Information |
|
RPS-10 HD
115VAC Heavy Duty, 15 Amp Remote Power Control/Reboot Unit (One
Plug, Expandable)
A heavy duty, 15 amp version of our RPS-10 expandable, code controlled
power control/reboot system. A single RPS-10 HD Master Module provides
15 amp power control for one AC outlet. When reboot needs expand,
additional RPS-10 HD Satellite Modules can be added to allow individual
control of up to ten AC outlets. Modules are linked together using
standard RJ-11 style cable, for a maximum end-to-end length of 2000
feet.
More Information |
 |
Call Power II
Economical Ring-Activated Reboot Unit (One Outlet)
The Call Power II provides an economical solution for applications that require
power control/reboot capabilities for a single 115 VAC outlet. The Call Power
II responds to a unique ring sequence to automatically reboot power, or temporarily
switch power On for a user-selected time period.
More Information |
|
WTI Home
Bomara Homepage