Powerware 9125 200-240VAC Specs

Electrical Input
Nominal Voltage	230 Vac (user-selectable for 200, 220, 230, and 240 Vac See Model Selection Guide
Power Ratings	700 - 2000VA; See Model Selection Guide
Voltage Range	160 - 288V (without using batteries)
Input Power Factor	>.95, typical
Frequency	50/60 Hz, autosensing
Frequency Range	45 - 65 Hz
Electrical Output
On Utility Voltage Regulation	+/-3% of nominal
On Battery Voltage Regulation	+/-3% of nominal
Efficiency	89 - 92%, depending on load
Frequency Regulation	+/- 3 Hz online; +/- 0.1 Hz on battery
Load Crest Factor	3 to 1 ratio
Battery
Internal Battery type	Sealed, lead-acid; maintenance free 700/1000VA: (2) 12V, 9 Ah 1250-2000VA: (4) 12V, 9 Ah
EBM Battery Type	PW9125 24 EBM: (8) 12V, 9 Ah PW9125 48 EBM: (8) 12V, 9 Ah
On Battery Runtime	See Battery Runtimes
Battery Replacement	Hot-swappable internal and external batteries
Recharge Time	<2 hrs. from complete discharge to 80% capacity at nominal line conditions
Start-On-Battery	Allows start of UPS without utility input
Communications
Serial Port	RS-232 communications port standard
Communications Cable	6-foot communications cable included
ConnectUPS-M SNMP Module (Optional)²	SNMP card adds direct control and monitoring capabilities in SNMP-based networks
RS-232 Multi-Port Module (Optional)²	Equipped with (6) communications ports to provide serial communication to multiple devices
USB Module (Optional)²	Allows UPS to communicate with Windows 98 computers via USB port; factory-installed option only
General
Topology	True online, double-conversion
Diagnostics	Full system self-test on power up
UPS Bypass	Automatic on overload or UPS failure
Dimensions and Weights	See Model Selection Guide
Environmental and Safety
Safety Markings	UL, CSA, CB, CE, S, D, N, FI, B, R
EMC Markings	FCC Class B and VCCI Class II, CE, NZ, TAIWAN
Surge Suppression	IEEE/ANSI C62.41 Category B (formerly 587)
Audible Noise	<45 dBA (on utility); <50 dBA (on battery)
Storage Temperature	0^o to 25^o C (32^o to 77^o F)
Relative Humidity	5 to 90%%, non-condensing
REPO Port	Meets NEC code 645-II intent and UL requirements
Network Transient Protector	In and out jack for telephone/modem protection of 10Base-T network cable; UL497A tested
¹Due to continuing product improvement programs, specifications are subject to change without notice. ²Optional in place of RS-232 serial port.

Model Selection Guide

RoHS Products

Available Options

Battery Runtimes (in minutes)

700/1000 VA Models

Load

Standard
Internal
Batteries

1 EBM

2 EBMs

200VA/140W

271

546

400VA/280W

142

278

700VA/490W

156

850VA/595W

124

1000VA/700W

104

Load	Standard Internal Batteries	1 EBM	2 EBMs	3 EBMs	4 EBMs
1250-2000 VA Models
400VA/280W	46	177	331	501	682
700VA/490W	25	96	180	272	370
850VA/595W	21	76	142	214	292
1000VA/700W	16	61	115	174	237
1250VA/875W	11	46	87	131	179
1500VA/1050W	8	37	70	106	144
1800VA/1260W	6	30	57	85	116
2000VA/1400W	5	26	49	74	100

Battery Times are approximate and may vary with equipment, configuration, disk access, battery age, temperature, etc.

Powerware 9125

Model Selection Guide

RoHS Products

Available Options

Battery Runtimes (in minutes)

Legacy Products