GarrettCom Utility Networks > Substation Routers > Industrial Frame Routers > DS2000-IFR

DynaStar 2000 Industrial Frame Router


This product is now discontinued, for any additional support or replacements please Contact Bomara or visit our Router Products


Supporting 16 serial ports, and Ethernet interfaces with either eight 10/100 TX, or six 10/100 TX with two 100 FX and two GigE ports, and dual T1/E1 or DDS WAN interfaces, the DynaStar 2000 Industrial Frame Router (IFR) delivers reliable and secure WAN connectivity to multiple industrial automation devices at your site.

The DynaStar DS2000-IFR is the only integrated WAN device specifically designed for industrial monitoring and control networks operating in harsh environments. Combining 5 different networking functions (terminal server, Ethernet switch, IP router, frame relay access device and DSU/CSU), the DS2000-IFR is the only device available that can replace multiple WAN communication devices on your network, increasing operational reliability and significantly reducing hardware and deployment costs.

A "hardened" product, the DS2000-IFR is built to thrive in the harshest environments and conditions, including: extreme temperatures, high humidity, power surges, ground potential rise, EMI/RFI interference as well as other tough environmental conditions often found in industrial and remote process sites.

The DS2000-IFR supports multiple application and device interfaces including legacy bit-oriented protocols, Async/serial protocols and IP/Ethernet. The DS2000-IFR is ideally suited to enable IP conversion strategies for SCADA traffic, and other non-IP based process control, supervisory or monitoring communications traffic. The DynaStar 2000 IFR uses SCADA Frame Forwarding technology for low overhead, high performance support of delay sensitive serial SCADA applications.

The DS2000-IFR consolidates data from multiple devices onto a common platform, then on to a wide area network connection. The primary WAN interface is based on frame relay over private or carrier services. The platform can also function locally as both an Ethernet switch and an Async-TCP/IP terminal server.

FEATURES

  • Hardened for harsh environments
  • Meets IEEE 1613 / IEC 61850-3 requirements for power utility substations
  • Five networking functions integrated in one product
    • Terminal server
    • Ethernet switch
    • IP router
    • Frame Relay Access Device
    • DSU/CSU
  • 16 serial ports, 300bps to 230.4kbps
  • Eight 10/100 Base TX auto-sensing Ethernet ports OR Six 10/100 Base TX auto-sensing Ethernet ports with 2 (MM or SM) 100 FX and 2 SM GigE SFP ports
  • 2 DDS or T1/E1 WAN ports with integrated DSU/CSU
  • Multi-protocol support
    • Async, SCADA, Ethernet, TCP/IP, Frame Relay
    • Secure SCADA / Frame Relay transport
    • Ethernet switching
      • Flow control
      • Prioritization
      • VLANs
      • Rapid Spanning Tree
    • IP Routing, RIP, RIP II, RIP RX, OSPF, Static
    • IP VPN using IPSec
    • VLAN support
    • IP address filtering
    • DHCP & BootP services
  • Menu-driven and SNMP management
  • Port mirror on Ethernet switch ports
  • Powerful built-in protocol analyzer
  • No fans or moving parts
  • Non-vented sealed steel enclosure
  • AC & DC power options

Technical Specifications

WAN INTERFACE

Physical Interface:

  • 2 Connectors: RJ-48
  • Dual DDS WAN option: 56/64k DDS
  • Dual T1/E1 WAN option: Line Rate 1.544Mbps nx56/64k
  • Integral CSU/DSUs

Protocols/Features:

  • Frame Relay, IP

SERIAL INTERFACE

Physical Interface:

  • 16 RS232/V.24 serial ports
  • RJ45 connector
  • Serial data rates from 300bps to 230.4kbps
  • Data length: 1-32 bits supporting legacy SCADA protocols

Protocols/Features:

  • Async to TCP/IP
  • TCP/IP to serial terminal server, reverse terminal server
  • Select SCADA bit oriented protocols CONITEL, PMS91, MCS-11, GETAC
  • SCADA frame forwarding over Frame Relay

ETHERNET INTERFACE

Physical Interface:

  • 6 or 8 RJ-45 modular connector ports
  • 10/100 Base TX, auto-sensing or fixed speed
  • Full Duplex, Half Duplex with auto MDIX
  • 2 optional 100 FX and 2 optional GigE ports

Protocols/Features:

  • Ethernet, TCP/IP
  • Full wire speed switching between ports
  • IEEE 802.3x flow control
  • Prioritization per IEEE 802.1p
  • Port based VLANs per 802.1Q
  • Spanning Tree per IEEE 802.1d
  • Rapid Spanning Tree per IEEE 802.1w
  • Support for 4096 MAC addresses

IP ROUTING FUNCTIONS AND FEATURES

  • IP Routing, RIP, RIP II, RIP RX, OSPF, Static Routes
  • DHCP & BootP Services
  • Block/Allow MAC, IP, or PORT addresses
  • Prioritize traffic streams over Frame Relay and/or DiffServ
  • Secure SCADA / frame relay transport
  • IP or frame relay single port to multicast for SCADA polling

SECURITY

  • Multilevel passwords with enforcement and aging
  • Firewall with IP address filtering
  • IP VPN using IPSec with DES/3DES encryption
  • VLAN support on Ethernet LAN segments
  • Static MAC address

MANAGEMENT AND DIAGNOSTICS

  • Local console port to menu-driven system
  • Remote access via telnet from WAN or Ethernet connection
  • SNMP MIB and SNMP traps
  • DDS CSU and DSU loop-back features
  • PING and telnet diagnostic functions
  • Port mirror on Ethernet switch ports
  • Powerful built-in Datacom analyzer to monitor traffic on any port
  • Comprehensive Layer 1 through 3 statistics
  • Event logging

ENVIRONMENTAL

Operating Temperature:
-20C to +60C, no fans

Storage Temperature:
-40C to +85C

Humidity:
95% non-condensing

Industrial:
IEEE1613
IEC 61850-3

Emissions:
EN55022A, FCC Part 15A
VCCI, AS/NZ-3548

Safety:
UL60950-1
EN60950-1
CSA C22.2

Immunity:

  • EN55024
  • EN61000-6-2
  • EN61000-4-2 (ESD)
  • EN61000-4-3 (RF)
  • EN61000-4-4 (EFT)
  • EN61000-4-5 (SURGE)
  • EN61000-4-6 (CRF)
  • EN61000-4-11 (VDI)

Environmental Monitoring:
Dry Contact Alarm, 1 output

Telecom:

  • ACTA TIA/EIA IS-968A (FCC part 68)
  • IC CS03
  • EN55022:1998 Telco Port Emissions

POWER OPTIONS

High Voltage (H)

  • 90-250 VAC or VDC, 50-60Hz
  • 1A, 85 watts

Low Voltage DC (L)

  • 18-60 VDC
  • 4.5A, 81 watts

MECHANICAL

Dimensions:
19-inch rack mount, 1.5U
17.5"W x 10"D x 3.5"H
(44.5cm x 25.4cm x 8.89cm)

Weight:
11 lbs (5 kg)

Mounting:
Front rack mount, mid-mount, or panel mount options

* Planned Features



Call Us: 1-978-452-2299
First Name:
Last Name:
Company:
Address:
Mail Stop:
City:
State (if in US):
Province/Region (if outside US):
Country:
ZIP (Postal) Code:
E-mail:
Telephone:
Fax:
Questions/Comments:
Verification:

View Full Site View Mobile Optimized