Bomara Home » Server Technology Products » Smart IP PDU » Smart CS-36V5 415V 20/30A 3Ph 24xC13 & 12xC19 with PIPS

 Smart CS-36V5: 415V 20/30A 3 phase 24xC13 & 12xC19 with PIPS
  3 phase PIPS, Per Infeed Power Sensing, power distribution, 36 outlets with LED input current displays and IP monitoring; 415V high-density.

• All the products featured on this page are discontinued except for the additonal ordering information and accessories


CS-36V5-A4



  • Description
  • Specifications
  • Gallery

This three phase Sentry PIPS CDU combines all of the features of a Smart CDU with the ability to provide power monitoring per inlet/infeed. Power information per infeed includes current, voltage, power, apparent power, crest factor, reactance, power factor and accumulated energy. This information replaces branch circuit monitoring devices typically installed in the power distribution panel or remote power panel (RPP) with higher accuracy and lower cost monitoring of each circuit attached to the CDU.

Combine the Sentry PIPS Smart Cabinet PDU with the Sentry Power Manager (SPM) software tool to gain power usage information across multiple Cabinet PDU's individual IP address.

This Smart cabinet PDU delivers reliable power distribution, local power monitoring via LEDs, power monitoring via IP and environmental (temperature & humidity) monitoring via IP.   

Increasing power demands and density in the equipment cabinet requires new functionality from your cabinet PDU.  The Sentry cabinet PDU product family uniquely meets these demands. 

The Sentry Cabinet Power Distribution Unit (cabinet PDU) is an intelligent PDU with local LED input current monitoring, allowing network engineers to utilize the cabinet PDU's True RMS Power Monitor to precisely measure the current (in amps) that network devices are drawing on the power circuit. As new equipment units are added to the power drop, immediately observe its impact on the cumulative current draw. This allows the engineer to safely load each circuit to its maximum allowable load capacity without the danger of overloading the power circuit.   

The cabinet PDU meets new UL 60950-1 Branch Circuit Protection requirements. Now you can safely run 30-amp power drops to your server cabinet where individual outlet receptacles have lower output ratings (i.e., 20-amps). 




Remote Power Monitoring

Monitor input power via IP or serial interface.

HTTP/HTTPs Web Configuration & Control

Use the Sentry Web interface to configure each unit's network settings. SNMP traps for environmental & power thresholds and firmware updates. Also use the Web interface to monitor key values, including amperage load(s), temperature/humidity and other environmental conditions. SSL security provides a secure HTTPs connection.

SNMP Management & Event Notification

The Sentry family of products supports the Simple Network Management Protocol (SNMP). This allows network management systems to use SNMP requests to retrieve information such as input power, temperature and humidity. The Sentry includes an SNMP v1 agent supporting standard MIB I and MIB II objects. A private enterprise MIB extension (Sentry3 MIB) is also supported to provide remote power control. SNMP traps can be generated for various events, including Input Current Load Thresholds (min & max), Temperature Thresholds (min & max), Humidity Thresholds (min & max), water indication, and closed contacts (cabinet doors open/close).

Add a Second Tower

Connect an Expansion Cabinet PDU to this Smart Cabinet PDU to control two power input circuits and monitor power in the Data Center cabinet (individual or groups) under 1 IP address - our exclusive strategy for managing dual power-supply servers.

Zero U Enclosure

A vertical enclosure that occupies Zero Vertical U of rack space in the equipment cabinet. It mounts on the back rails or in the cavity space of the cabinet.

Secure Access - SSH or SSL Protection

Secure Shell (SSH), known as Secure Socket Shell, is a Unix-based command interface and protocol for securely getting access to a remote device.  Sentry supports SSHv2. Secure Sockets Layer (SSL) is a commonly-used protocol for managing the security of a message transmission on the Internet. SSL is an integral part of most Web browsers (clients) and Web servers.  Sentry supports SSLv3/TLSv1.

Integrated Temp/Humidity Probe Support

Two (2) RJ-style connectors located on the face panel of the PDU's enclosure provide support for two (2) Integrated Temperature & Humidity Probes with ten-foot (10') cables provide real-time measurements in the data center cabinet.

Firmware Flash Upgradable

Access new firmware updates via FTP for new firmware features and code releases. An update to the firmware does not affect the status of the power outlets.

LDAP/LDAPS

The sentry family of products supports Lightweight Directory Access Protocol (LDAP) Version 3 including LDAPS (LDAP over TSL/SSL). This support enable authentication with LDAP servers; user accounts do not need to be individually created locally on each Sentry device.
This allows administrators to pre-define and configure (in each Sentry product, and in the LDAP server) a set of necessary LDAP groups, and access rights for each. User's access rights can then be assigned or revoked simply by making the user a member of one or more pre-defined Sentry LDAP groups. User account can be added, deleted, or changed in the LDAP server without any changes on individual Sentry products.
Sentry LDAP support has been tested in the following environments:
  - Microsoft Active Directory (MSAD)
  - Novell eDirectory (eDir)
  - Open LDAP

RS-232 Control

Serial control via any device with a bi-directional serial port, including a PC, laptop, KVM switch, Console Port Access switch, or terminal server.


Sentry  CDU Specifications
Item # Available Input
Voltages
Rated Amperage Available Input Cord** Outlets Dimensions
(L x W x D)
PIPS CS-36V5-3 phase
CS-36V5Z454-A4C
CL-36V5Z454-A4C*
3-Phase Wye, 
240/415 V
50/60Hz
 30A NEMA L22-30P
Cordset, 10ft (3m)
(24) IEC 60320/C13
(12) IEC 60320/C19
73.5 x 1.75 x 3.5 in.
(1867 x 44 x 89 mm)
CS-36V53454-A4C
CL-36V53454-A4C* 
3-Phase Wye, 
240/415 V
50/60Hz
 20A IEC 60309
Cordset, 10ft (3m)
(24) IEC 60320/C13
(12) IEC 60320/C19
73.5 x 1.75 x 3.5 in.
(1867 x 44 x 89 mm)
CS-36V54454-A4C
CL-36V54454-A4C* 
3-Phase Wye, 
240/415 V
50/60Hz
 30A IEC 60309
Cordset, 10ft (3m)
 (24) IEC 60320/C13
(12) IEC 60320/C19
73.5 x 1.75 x 3.5 in.
(1867 x 44 x 89 mm)
**Click here to view additional information on Power Cords and Cables

 

Additional Ordering Information


Part Number Input Output
Master Expansion Rating, North America GS Input Type Output Rating North America GS Outlet: North America GS Outlet Type Branch Circuit: North America/GS Phase: North America/GS
CS-36V4J454-A4C CL-36V4J454-A4C   240/400V 3W+N+PE, 50/60Hz; 16A IEC 60309 16A   230V, 50/60Hz; <=48A   12xC19 <= 16 each, 24xC13 <= 10A each IEC 60320 C13/C19 /L1a,L1b,L2a,L2b,L3a,L3b <=16A /L1,L2,L3 <= 16A
CS-36V4K454-A4C CL-36V4K454-A4C   240/400V 3W+N+PE, 50/60Hz; 32A IEC 60309 32A   230V, 50/60Hz; <=96A   12xC19 <= 16 each, 24xC13 <= 10A each IEC 60320 C13/C19 /L1a,L1b,L2a,L2b,L3a,L3b <=16A /L1,L2,L3 <= 32A
CS-36V53454-A4C
(Discontinued)
CL-36V53454-A4C
(Discontinued)
240/415V 3W+N+PE, 50/60Hz; 16A   IEC 60309 16A 240V, 50/60Hz; <=48A       IEC 60320 C13/C19 L1a,L1b,L2a,L2b,L3a,L3b <=20A L1,L2,L3 <= 16A
CS-36V54454-A4C
(Discontinued)
CL-36V54454-A4C
(Discontinued)
240/415V 3W+N+PE, 50/60Hz; 24A   IEC 60309 24A 240V, 50/60Hz; <=72A       IEC 60320 C13/C19 L1a,L1b,L2a,L2b,L3a,L3b <=20A L1,L2,L3 <= 24A
CS-36V5Z454-A4C
(Discontinued)
CL-36V5Z454-A4C
(Discontinued)
240/415V 3W+N+PE, 50/60Hz; 24A   NEMA L22-30P 240V, 50/60Hz; <=72A   12xC19 <= 16A each, 24xC13 <= 12A each   IEC 60320 C13/C19 L1a,L1b,L2a,L2b,L3a,L3b <=20A L1,L2,L3 <= 24A/

 

  Additional Features and Specifications

Standards
> cTUVus – UL 60950-1-2003
> CAN/CSA 22.2 No. 60950-1:2003
> FCC Class A, Part 15
> CE
> EMC-EN 55022 Class A, EN 55024, CISPR 22 Class A

Communications
> 10/100 BaseT Ethernet
> HTTP/HTTPS
> SSLv3/TLSv1
> SNMPv2
> SSHv2
> Telnet
> LDAPv3 and LDAPS
> TACACS+
> RADIUS
> RS-232 (Serial)

Branch Circuit Protection
> Compliant to UL 60950-1

Accessories
> Temperature & Humidity Probe 
    - EMTH-1-1 Temperature & Humidity Probe, 10 ft (3 m)
    - EMCU-1-1B add 2 additional Temperature & Humidity ports, 4 contact-closure monitoring ports and 
      1 water sensor port

 




Call Us: 1-978-452-2299
First Name:
Last Name:
Company:
Address:
Mail Stop:
City:
State (if in US):
Province/Region (if outside US):
Country:
ZIP (Postal) Code:
E-mail:
Telephone:
Fax:
Questions/Comments:
Verification:

View Full Site View Mobile Optimized