Need Help? Call Us
Need Help? Call Us
|CPS » Remote Reboot Switches AC Power Control » 3P-RRC|
THREE PORT REMOTE REBOOT CONTROLLER (3P-RRC)
Provides Remote Reset Control for up to THREE Ports Over a Single Dial Line
The THREE PORT REMOTE REBOOT CONTROLLER (3P-RRC) is an out-of-band (dial-line) reset controller that is primarily used to selectively reset equipment connected to each of its three Control Ports through a series of Touch-Tone commands.
The 3P-RRC can be installed on any analog dial-line and can share the line with other normal voice, modem, fax or PBX requirements. The shared Default Port can support the phone equipment and a Reset device simultaneously, if required.
It can also be used as a security device by simply using it to turn the remote equipment, such as a modem, ON or OFF.
Note that the 3P-RRC is a controller only. It has three RJ-11 ports and requires a CPS Base Unit (such as an Intelligent AC Power Strip or an RJ-Cable Assembly) on each port that you wish to control. They are connected to the 3P-RRC via an RJ-11 connector. They can be physically located locally or up to 2000' from the controller, using standard phone or LAN cable.
The Intelligent AC Power Strip is normally used when the target machine does not have a reset button or when direct power ON/OFF control is also required. It has six AC outlets: two (2x4), four (4x2), or all six (6x0) may be designated as "Controlled Outlets" at the time of the order. The others may be used as normal surge protected AC outlets for printers, monitors or other equipment that do not require resets or On/Off control.
The RJ-Cable Assembly allows the 3P-RRC to perform a push-button reset (soft reset) on a PC. To use it, the target machine must have a Reset button that connects to the motherboard. It installs in a vacant I/O opening on the back of the machine's case, but does not require a slot on the motherboard. The connecting cables allow the Reset button to also be used normally.
However, these motherboards can also be used with the Auto Push Board (APB). The APB performs the first option above by pushing the Power Button once AC power returns. (See Resetting ATX Motherboards.)
How to control it
A typical touch-tone command may be:
How it works
THREE PORT REMOTE REBOOT CONTROLLER (3P-RRC) Item No SWT3PRRC Price Contact Bomara Also Available Item No SWTSPRRC (1 Port) Price Contact Bomara Item No SWTMPRRC (8 Ports) Price Contact Bomara Physical 4.5" W x 3" D x 1.25" H, 1 lb. Connectors (4) RJ-11 TelCo, Reset Control LEDs (5) Power, Mode Switches (1) 4-Bit Dip, (1) Pushbutton Bell None Cable (1) 5' RJ-11 Phone Cable Adaptor None AC Power Wall Mount 9VAC 1A, 115V/60Hz NOTE: For 220V/50Hz, add (-INT) to the Item No ------ NON-ADDRESSABLE BASE UNITS ------ OPTIONAL INTELLIGENT AC POWER STRIP 2 Controlled and 4 "Normal" Outlets Item No SWTAC6-A2-2x4 Price Contact Bomara 4 Controlled and 2 "Normal" Outlets Item No SWTAC6-A2-4x2 Price Contact Bomara 6 Controlled Outlets Item No SWTAC6-A2-6x0 Price Contact Bomara Physical 12" W x 2.5" D x 1.5" H, 2 lbs. Connectors (2) RJ-11 TelCo/Control, (6) AC Receptacles LEDs (1) Surge Protection Switches (1) Main Toggle On/Off Bell None Cable (1) 5' RJ-11 Phone Cable Adaptor None AC Power 115V/60Hz, 15 Amps NOTE: For 220V/50Hz, see the IPC. OPTIONAL INTERNATIONAL POWER CONTROLLER (IPC) See the IPC OPTIONAL PC-RJ CABLE INTERFACE ASSEMBLY Item No CAPC2-RJ Price Contact Bomara Physical 5.5" W x 2.5" D x .75" H, .25 lbs. Connectors (1) RJ-11 Interface, (4) PC Headers Pins LEDs None Switches None Bell None Cable (1) 2' M/F Reset Switch Cable, (1) 2' F/F Motherboard Reset Cable, (1) 5' RJ-11 Cable Adaptor None AC Power None OPTIONAL RELAY BOX See the Relay Box -------- ADDRESSABLE BASE UNITS -------- OPTIONAL A/B, MATRIX or X2 SWITCH See the AB-M OPTIONAL INTELLIGENT AUTO PUSH BOARD (I-APB) See the APB OPTIONAL INTELLIGENT POWER NODE (IPN) See the IPN